| Coolant (range) | 9.7–14.8 US qt · 9.2–14 L |
|---|---|
| Wheel-nut torque | 111 lb-ft · 150 N·m |
Per-engine engine-oil and coolant capacities for the Chrysler 300 (LX) (2005 – 2010), read from the manufacturer's owner's manual and cited per value. Oil figures are the service-refill quantity with a new filter; where the generation offers more than one engine the figures differ — match the row to your engine. Fill quantities differ by procedure: a drain-and-fill is usually less than a dry (overhaul) fill — confirm the method in the manual before topping up.
Per-engine fluids 4 engines
| Engine | Engine oil (with filter) | Oil viscosity | Oil spec / standard | Coolant |
|---|---|---|---|---|
| Chrysler 2.7L EER V6 SOHC | 6.0 US qt · 5.7 L[1] | SAE 5W-30[1] | Mopar MS-6395[1] | 9.7 US qt · 9.2 L[1] |
| Chrysler 6.1L SRT8 HEMI V8 (ESF, 425 hp) | 7.0 US qt · 6.6 L[1] | SAE 0W-40[1] | Mopar MS-10725 (full synthetic)[1] | 14.8 US qt · 14 L[1] |
| Chrysler 5.7L HEMI V8 (EZB, MDS, 2003-2008) | 7.0 US qt · 6.6 L[1] | SAE 5W-20[1] | Mopar MS-6395[1] | 14.6 US qt · 13.8 L[1] |
| Chrysler 3.5L EGG V6 SOHC | 6.0 US qt · 5.7 L[1] | SAE 5W-30[1] | Mopar MS-6395[1] | 10.6 US qt · 10 L[1] |
Other fluids & capacities 7
| Fluid | Capacity | Spec / viscosity |
|---|---|---|
| Brake fluid[1] | — | DOT 3 (SAE J1703) |
| Transmission fluid[1] | 5.3 US qt · 5 L · NAG1 service fill | — |
| Power Steering Fluid[1] | — | Mopar Power Steering Fluid +4 (or Mopar ATF+4) |
| Washer fluid[1] | — | Mopar Windshield Washer Solvent (or equivalent low-temp formula) |
| Transfer case[1] | 0.6 US qt · 0.6 L · fill qty — verify in manual | Mopar Transfer Case Lubricant LX (PN 05170055AA, AWD only) |
| Differential Front[1] | 0.6 US qt · 0.6 L · fill qty — verify in manual | 75W-90 GL-5 Synthetic Gear Lubricant (AWD only) |
| Differential Rear[1] | 1.5 US qt · 1.4 L · fill qty — verify in manual | 75W-140 GL-5 Synthetic Gear Lubricant |
From the manufacturer's workshop / owner documentation for this generation. Gen-wide figures — some values can vary by trim or model year. Fill quantities differ by procedure: a transmission or axle “service” drain-and-fill is often far less than the dry capacity — always confirm the exact fill method in the manual before filling.
Drain & wheel torque 2
Frequently asked
- What is the engine oil capacity of the Chrysler 300 (LX) (2005 – 2010)?
- Engine oil capacity with a new filter is 7.0 US qt · 6.6 L and differs by engine — match the row in the per-engine table above to your engine code. This is the service-refill quantity, not the dry/overhaul fill; add most of it, then top up to the dipstick mark and use the viscosity grade listed above. Verified from the manufacturer's documentation and cited.
- What is the coolant capacity of the Chrysler 300 (LX)?
- The total cooling-system capacity (including the heater core and expansion tank) is 9.7 US qt · 9.2 L, varying by engine. A routine drain-and-fill replaces less than the full system, so bleed the air and re-check the level warm. Use the coolant type specified for this vehicle — mixing incompatible coolants reduces corrosion protection. Verified from the manufacturer's documentation.
- What is the wheel-nut (lug) torque for the Chrysler 300 (LX)?
- Wheel-nut (lug) torque is 150 Nm. Tighten in a diagonal (star) pattern in two or three even stages, on clean, dry threads, and re-check after roughly 80 km (50 miles) of driving — the most common cause of warped brake discs is uneven or over-torqued wheel nuts. Verified from the manufacturer's documentation.
Sources
- Chrysler LX Factory Service Manual (300 / Charger / Magnum, 2005-2010)OEM owner's-manual portalFactory service manual. Fluid capacities p30; oil viscosity p26; wheel/lug p8446; HEMI oil-drain p6270/6438.Retrieved 2026-11-08